PERANCANGAN RECOIL SPRING COVER UNTUK EXCAVATOR PC1250-8 DI PT XX

Penulis

  • Vuko Arief Tua Manurung Politeknik Astra Jakarta Indonesia
  • Dleva Elkhaq Haeda Illiyin Politeknik Astra Jakarta Indonesia
  • Amir Amir Universitas Muhammadiyah Tangerang image/svg+xml

DOI:

https://doi.org/10.31000/mbjtm.v7i1.8383

Kata Kunci:

Autodesk Inventor 2020, Cover, Recoil spring

Abstrak

Maintenance adalah proses pemeliharaan atau perawatan terhadap sesuatu asset berupa barang bergerak maupun tidak bergerak. Dalam bisnis alat berat, maintenance adalah serangkaian proses yang bertujuan untuk memastikan mesin atau peralatan lainnya dapat digunakan secara berkelanjutan dan efisien dalam jangka waktu yang dikehendaki. Rusaknya recoil spring pada excavator PC1250-8 merupakan kasus yang sering terjadi, disebabkan kondisi unit yang baru belum dilengkapi dengan komponen tambahan berupa penutup (cover) sehingga dapat mencegah masuknya kotoran ke recoil spring. Akibatnya adalah rusaknya komponen recoil spring disebabkan oleh tanah, batu/krikil, dan kotoran lainnya yang masuk dan mengendap di sekitar area gerak (inner frame). Dari persoalan tersebut maka didisain suatu perancangan cover untuk mencegah kotoran masuk ke dalamnya. Proses perancangan ini menggunakan alat bantu software Autodesk Inventor 2020.

Referensi

https://products.unitedtractors.com/id/berita/komatsu-hydraulic-excavator-pc1250-8r/

Manurung, V.A., Sutama, Y.C. and Manalu, E.S., 2020. Menurunkan Kerusakan yang Tidak Terjadwal pada Komatsu PC1250SP–8 Dengan Melakukan Reposisi Line Hose Autolube di PT PPN, District Kideco. Technologic, 11(1).

Manurung, V. A. T., & Poetra, R. I. (2018, February). Auto Drain Valve Water Separator inside the Unit of Komatsu HD 465-7R. In IOP Conference Series: Materials Science and Engineering (Vol. 306, No. 1, p. 012128). IOP Publishing.

Manurung, V. A., Joko, Y. T., & Santosa, A. (2020, May). Reducing the High Temperature of Water Radiator Dump Truck (HD 785-7 Type) by Making Special Tool. In IOP Conference Series: Materials Science and Engineering (Vol. 846, No. 1, p. 012067). IOP Publishing.

Manurung, V.A., Trirahardjo, W. and Ichwan, B., 2020. Mengurangi Waktu Pengerjaan Autolube PC2000-8 Dengan Grease Clogging Detector di PT. UT daerah Bengalonsangkulirang. Technologic, 11(2).

VAT Manurung, FRSR Tambunan, YC Sutama (2013), Mengurangi Resiko Kerusakan Auto Priming Pump pada Dump Truck Tipe HD785-7 di PT UT site Batu Kajang Kalimantan Timur. Authors.

Michael F. Ashby, (2005), Materials Selection in Mechanical Design, 3th Edition, Butterworth-Heinemann, Linacre House, Jordan Hill, Oxford OX2 8 DP 30 Corporate Drive, Burlington, MA 01803.

Kurniawan, P., Andoko, A. & Putu, W.S. 2021, "Leaf spring type simulation with finite element method approach", IOP Conference Series.Materials Science and Engineering, vol. 1034, no. 1.

Ratekkar, A., Gulhane, S., Meshram, S., Borker, M., Khan, A.R. & Shelke, R.S. 2022, "Development of Coil Spring Suspension System with Air Bellows", IOP Conference Series.Materials Science and Engineering, vol. 1259, no. 1, pp. 012026.

Kumbhalkar, M.A., Bhope, D.V. & Vanalkar, A.V. 2016, "Analysis of Rail Vehicle Suspension Spring with Special Emphasis on Curving, Tracking and Tractive Efforts", IOP Conference Series.Materials Science and Engineering, vol. 149, no. 1.

Zeng, Q., Liu, W., Wan, L., Wang, C. & Gao, K. 2020, "Maintenance Strategy Based on Reliability Analysis and FMEA: A Case Study for Hydraulic Cylinders of Traditional Excavators with ERRS", Mathematical Problems in Engineering, vol. 2020.

Zhang, Y. & Sun, G. 2020, "Informationization and Big Data Technology in Management and Maintenance of Mining Equipment in Large Open Pit Mines", Journal of Physics: Conference Series, vol. 1574, no. 1.

Odeyar, P., Apel, D.B., Hall, R., Zon, B. & Skrzypkowski, K. 2022, "A Review of Reliability and Fault Analysis Methods for Heavy Equipment and Their Components Used in Mining", Energies, vol. 15, no. 17, pp. 6263.

Dyorina, N.V., Velikanov, V.S. & Dyorina, K.S. 2020, "Identification of failure patterns of excavator equipment failures considering the control factor", IOP Conference Series.Materials Science and Engineering, vol. 971, no. 4.

Cipto, Rahangmetan, K.A., Sariman, F., Hariyanto, Bahar, S.B. & Sapsal, M.T. 2019, "Stress analysis on the frame of peanut skin peeler using autodesk inventor software", IOP Conference Series.Earth and Environmental Science, vol. 343, no. 1.

Goanta, A.M. 2017, "Aspects on 3rd Design of Assemblies and Part Lists Customizing with Inventor 2016", Journal of Industrial Design and Engineering Graphics, vol. 12, no. 1, pp. 115-118.

Magomedov, I.A. & Sebaeva, Z.S. 2020, "Comparative study of finite element analysis software packages", Journal of Physics: Conference Series, vol. 1515, no. 3.

Ing-Chang, J. & Springer, W. 2009, Teaching Von Mises Stress: From Principal Axes To Nonprincipal Axes, American Society for Engineering Education-ASEE, Atlanta.

Marasescu, D., Ristea, M., Popa, A., Scurtu, I. & Pruiu, A. 2016, "Considerations Regarding the Von_Mises Stress Developed on a 2000x100x4 mm Plate During the Impact with a 6.2 kg Cylindrical Body", Scientific Bulletin "Mircea cel Batran" Naval Academy, vol. 19, no. 2, pp. 344.

Gong, Y., Wang, P., Ge, W. & Yun-Bo, Y. 2019, "Numerical Simulation and Mechanism Analysis on the Concave Deformation of Automotive Dry Clutch Pressure Plate", Applied Sciences, vol. 9, no. 23, pp. 5017.

Unduhan

Diterbitkan

2023-06-28

Terbitan

Vol 7 No 1 (2023): Motor Bakar: Jurnal Teknik Mesin

Bagian

Articles

Lisensi

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

Motor Bakar : Jurnal Teknik Mesin have CC BY-NC or an equivalent license as the optimal license for the publication, distribution, use, and reuse of scholarly work.

In developing strategy and setting priorities, Motor Bakar : Jurnal Teknik Mesin recognize that free access is better than priced access, libre access is better than free access, and libre under CC BY-NC or the equivalent is better than libre under more restrictive open licenses. We should achieve what we can when we can. We should not delay achieving free in order to achieve libre, and we should not stop with free when we can achieve libre.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International (CC BY-NC 4.0) License

YOU ARE FREE TO:

  • Adapt — remix, transform, and build upon the material for any purpose, even commercially.
  • The licensor cannot revoke these freedoms as long as you follow the license terms