ANALISIS KEKUATAN SAMBUNGAN LAS SMAW PIPA GALVANIS 2 INCH PIPA PDAM DENGAN METODE UJI TARIK

Authors

  • Riki Candra Putra Universitas Muhammadiyah Tangerang image/svg+xml
  • rofiroh rofiroh Univeristas Muhammadiyah Tangerang

DOI:

https://doi.org/10.31000/mbjtm.v6i1.6665

Keywords:

Besi Pipa Galvanis, Uji Tarik, Kekuatan, Las SMAW.

Abstract

Air bersih merupakan suatu kebutuhan yang sangat penting dalam kehidupan manusia, terutama bagi masyarakat Indonesia yang negaranya terdiri dari banyak pulau yang memungkinkan kebutuhan air bersih di Indonesia sangat diperlukan. Untuk menyalurkan air bersih dibutuhkan pipa yang salah satunya menggunakan jenis material galvanis, karena material jenis pipa galvanis mempunyai ketahanan yang tinggi, tujuan dan manfaat penelitian yaitu dapat mengetahui proses, langkah, dan hasil dari analisis kekuatan sambungan las dengan metode uji tarik. Metode penelitian menggunakan bahan besi pipa galvanis yang disusun acak dengan ketebalan 1 mm, pengujian tarik di lakukan dengan standar SNI 07-0408-1989. Hasil pengujian tarik dari 3 spesimen pada besi pipa galvanis dengan kode tebal 1 mm memiliki hasil berbeda dikarenakan 1 dari 3 spesimen terputus pada bagian material dasar, dari 3 spesimen yang paling optimal yaitu pada spesimen 1 beban tarik 11,5 kN kuat tarik 387 N/mm2 dan 3940 Kgf/cm2.

References

Rafe`i, Ahmad. 2011. Material Teknik Uji Tarik, Jurusan Teknik Mesin. Fakultas Teknik, Universitas Sultan Ageng Tirtayasa.

Departemen Kimpraswil, 2002. Pedoman atau Petunjuk Teknis dan Manual, Bagian 6, Sistem Penyediaan Air Minum Perkotaan, Departemen Permukiman dan Prasarana Wilayah, Jakarta

Taufan Dyan Fachrudin & Dwi Heru Sutjahjo (2017). Laju Korosi Pipa Galvanis (Inlet Desalinasi) Pada Sea Chest Kapal Terhadap Waktu Dan Salinitas Air Laut. Jurnal Teknik Mesin Unesa Volume 05 Nomor 03, 87-94

Gapsari M F, Femiana, Pengaruh Kelembaban Elektroda E 7018 Pada Shielded Metal Arc Welding (SMAW) Dengan Metoda Permukaan Respon, Master Theses. (http://digilib.its.ac.id/ITS-Master-3100007030155/327, 2009)

Hajime Shudo. Uchidarokakuho Material Testing (Zairyou Shiken). 1983.

Sabri N, Syahrizal (2020). Analysis of Corrosion Rate in Centrifugal Pump Intake Pipes (Case Study: PDAM Bengkalis Indonesia). SINTEK JURNAL: Jurnal Ilmiah Teknik Mesin. Vol. 14 No. 1

Yonatan ,Franki Hutauruk (2017). Analisis laju korosi pada pipa baj karbon dan pipa galvanis dengan metode elektrokimia. Departemen Teknik Sistem Perkapalan Fakultas Teknologo Kelautan. Institut Teknologi Sepuluh November Surabaya.

Suratman, M., 2001, Teknik Mengelas Asetilen, Brazing dan Busur Listrik, Pustaka Grafika, Bandung.

Yustika Kusumawardani & Widi Astuti. Evaluasi Pengelolaan Sistem Penyediaan Air Bersih Di Kota Madiun, Jurnal Neo Teknika Vol. 4 No. 1, Juni 2018,

M, Wahyu. Idhar. 2015. Pengujian sambungan las pada bagian sasis belakang mobil shuttle bus dengan bahan profil UNP menggunakan metode uji tarik. Teknik Mesin.Universitas Muhammadiyah Tangerang.

William D. Callister Jr. John Wiley&Sons, Material Science and Engineering: An Introduction., 2004.Referensi jurnal/artikel/internet:

Asif Faiz, Walsh Michael P, Weaver Christopher S, (1996). Air Pollution From Motor Vehicles, Standards and Technologies for Controlling Emissions, The World Bank Washington, D.C, USA.

Avinash Kumar Agrawal, Shrawan Kumar Singh, Shailendra Sinha and Mritunjay Kumar Shukla (2003) “Effect of EGR on the Exhaust Gas Temperature and Exhaust Opacity in Compression Ignition Enginesâ€, Kanpur 208 016, India.

Cenk Sayin, Ahmet Necati, Mustafa Canakci (2009). The Influence of operating parameters on the performance and emissions of a DI diesel engine using metanol-blended-diesel fuel, International Journal of Fuel, Number 89, ScienceDirect.

Downloads

Published

2022-05-07

Issue

Vol. 6 No. 1 (2022): Motor Bakar: Jurnal Teknik Mesin

Section

Articles

License

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

Motor Bakar : Jurnal Teknik Mesin have CC BY-NC or an equivalent license as the optimal license for the publication, distribution, use, and reuse of scholarly work.

In developing strategy and setting priorities, Motor Bakar : Jurnal Teknik Mesin recognize that free access is better than priced access, libre access is better than free access, and libre under CC BY-NC or the equivalent is better than libre under more restrictive open licenses. We should achieve what we can when we can. We should not delay achieving free in order to achieve libre, and we should not stop with free when we can achieve libre.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International (CC BY-NC 4.0) License

YOU ARE FREE TO:

  • Adapt — remix, transform, and build upon the material for any purpose, even commercially.
  • The licensor cannot revoke these freedoms as long as you follow the license terms